Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Liner & Rebuild for Frankford Homeowners
A failed liner is the quiet problem behind most chimney trouble: combustion gases that should leave the house instead seep into living space, and creosote builds where it can’t be seen. If your Frankford home has a clay flue that’s cracked, spalled, or too wide for the appliance it serves, we repair or reline the system rather than patch the symptom. Chimney liner and rebuild work is the core of what we do, from a stainless steel liner installation to a partial or full masonry rebuild. Our technicians have up to 15 years of experience, and we work with the professional-grade brands chimney pros rely on. We install and service DuraFlex and HeatShield, among others. A sweep, a camera inspection, and a written scope come before any rebuild recommendation. Call (833) 962-9222 to book an assessment. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

What Our Chimney Liner & Rebuild Service Includes
Chimney work is all we do, which means we see liner and structural problems generalists miss. Below is how each part of the service works and when it’s the right call for your Frankford home.
Stainless Steel Liner
A stainless steel liner is a new flue pipe run inside the existing chimney, sized to the appliance and insulated so the flue stays warm. You need one when the original clay tiles are cracked, offset, or too large for a modern wood stove or insert, which lets creosote form and gases cool before they leave. We install rigid and flexible sections from product lines like DuraFlex and Olympia Chimney, sized to the appliance manufacturer’s spec, then seal the top and bottom so the liner vents only where it should.
Flexible Liner
A flexible liner is a corrugated stainless steel pipe that follows the curves and offsets in an older Frankford chimney that a rigid pipe can’t pass. It’s the usual choice when the flue has a bend or a damper frame in the way, and it’s common in the rowhouse stock around Frankford where chimneys were built tight. We size flexible liner from DuraFlex and Gelco to the appliance, insulate it where the flue allows, and support it so it doesn’t rest on the smoke shelf.
Liner Replacement
Liner replacement means pulling a failed or damaged liner and installing a new one, which is the standard fix when the original clay liner has cracked through or a previous liner has burned out. It matters because a compromised liner no longer keeps combustion gases inside the flue. We document the old liner’s condition with camera footage and a photo report before and after, so you can see what came out and what went in rather than taking our word for it.
Partial Rebuild
A partial rebuild replaces the damaged section of a chimney, usually the top courses above the roofline or the crown and flashing area, while the sound lower masonry stays in place. It’s the right call when spalling brick or a failed crown is isolated and the flue below is still solid. We strip the failed brick, rebuild the section with matched material, and reset the crown with a proper overhang so water sheds away from the flue instead of into it.
Full Chimney Rebuild
A full chimney rebuild takes the stack down and rebuilds it from the roofline up when the masonry has moved, leaned, or lost so much face that spot repairs won’t hold. It’s a structural job, not a cosmetic one, and it’s the point where a sweep-only company hands off to someone else. We handle the whole rebuild, from tear-down and flue re-lining to new crown and cap, so the chimney goes back together as one system and you don’t hire a second contractor.
Liner Repair
Liner repair restores a liner that’s damaged but still structurally sound, and in some cases it’s a real alternative to full relining. We apply HeatShield ceramic liner repair to rebuild cracked flue joints and restore a smooth, sealed surface from the inside, without tearing the chimney apart. That restorative process is one many sweep-only providers can’t offer, and it’s why a camera inspection comes first: not every liner can be repaired, and we tell you plainly when a replacement is the honest answer.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Liner & Rebuild
We install and service DuraFlex flexible and rigid liner, and we know where it wears: at the top plate, at the appliance connection, and at any point where the liner bends without proper support. We work with Olympia Chimney components for the same reason, matching the liner and fittings to the flue rather than forcing a generic pipe into a non-standard chimney. Gelco products come into play on liners and venting where the appliance calls for a specific configuration, and we size to the manufacturer’s spec every time.
HeatShield is the brand behind our ceramic liner repair, and it’s a different kind of work than installing new pipe: we’re restoring the existing flue surface from the inside, joint by joint. Famco products round out the line when a job calls for them. We’re not a dealer and we don’t claim to be, but we do know these systems and how they fail. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or any other make, we can help.
Signs You Need Chimney Liner & Rebuild Right Now
- Cracked or missing clay tiles inside the flue. A camera inspection shows the joints and faces of the original liner, and once tiles crack through, gases can reach the masonry around them. That’s a liner problem, not a cleaning problem.
- White staining or crumbling on the chimney’s exterior. Efflorescence and spalling brick usually mean moisture is getting in and the masonry is breaking down from the inside. Left alone, a crown-and-flashing repair turns into a partial rebuild.
- A leaning or visibly shifted stack. A chimney that’s pulling away from the house at the roofline is a structural warning, and it needs a full rebuild rather than a cosmetic patch. Don’t wait on this one.
- Smoke rolling back into the room or a draft that won’t pull. A flue that’s undersized for the appliance, or a liner that’s collapsed or blocked, will push smoke back instead of up. That’s a venting failure worth diagnosing before the next fire.
- Creosote glaze or a strong chimney odor between burns. Heavy glazed creosote is the fuel a chimney fire feeds on, and it often signals a flue that’s too cold or too large for the fire you’re building. A liner sized to the appliance fixes the cause.
Our Chimney Liner & Rebuild Process – Step by Step
- 1
Camera inspection and full-system assessment. We run a chimney camera down the flue and photograph the crown, flashing, and exterior masonry. You see the footage, and the photo report is included so you have a record of what we found.
- 2
Written scope and flat-price estimate. We put the recommended work, the alternatives, and the price in writing before anything is booked. If part of the job can safely wait, we say so. Nothing gets recommended without camera evidence you can review yourself.
- 3
Material selection sized to the appliance. We measure the flue and match the liner to the appliance’s venting requirements, choosing from DuraFlex, Olympia Chimney, or Gelco as the job calls for. For masonry rebuilds, we match brick and mortar to the existing stack.
- 4
Installation or rebuild. Liners go in insulated and supported, sealed at the top plate and the appliance connection. Rebuilds are stripped, rebuilt, and re-crowned with proper overhang so water sheds. We keep the work area contained and clean up behind us.
- 5
Final camera verification and photo report. We run the camera again after the job to confirm the liner is sound, sealed, and clear, and hand you the before-and-after images. That record is yours to keep for insurance, resale, or your own confidence.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Liner & Rebuild Cost in Frankford?
A typical stainless steel liner installation in Frankford runs $2,400 to $4,800 depending on flue height, liner diameter, insulation, and whether the top plate and cap need replacing. Liner repair with HeatShield usually falls in the $1,200 to $2,600 range, and it’s the lower-cost route when the flue can be restored rather than replaced. A partial rebuild, covering the crown and upper courses, typically runs $1,800 to $4,500. A full chimney rebuild from the roofline up is the largest job at $6,000 to $15,000 or more, driven by stack height, access, and how much of the masonry has to come down.

Here’s what moves the number: the number of flue tiles and how far the liner has to run, whether the chimney has offsets that demand flexible rather than rigid pipe, roof pitch and access, and how much of the crown and flashing needs rebuilding. To avoid overpaying, ask for a camera inspection and a written scope before you commit to anything, and get the liner sized to your appliance rather than sold the biggest pipe available. Our free estimate includes the camera inspection, the photo report, and a flat price agreed before booking, so the written estimate sets the final price. Call (833) 962-9222 for an exact quote – estimates are free.
Chimney Liner & Rebuild Near Frankford – Our Service Area
We work throughout Frankford and the surrounding neighborhoods, including Oxford Circle, Olney, Tacony, Kensington, and Port Richmond, plus West Philadelphia, Overbrook, Merion Station, Narberth, Penn Wynne, and Millbourne. Response across that area is quick, and a booked sweep or inspection puts a technician on site fast. If you’re searching for Chimney Sweep Frankford service with liner and rebuild capability under one roof, you’re in the right place. For the same work across the city, see our chimney liner & rebuild page for West Philadelphia.
Serving Frankford, PA – Our Local Coverage Area
We serve Frankford and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Liner & Rebuild in Frankford
Chimney liner and rebuild work covers two connected jobs: relining or repairing the flue so combustion gases vent safely, and rebuilding the masonry when the structure itself has failed. A liner is the passage the smoke travels through, and the rebuild is the brick, crown, and flashing that hold and protect it. We handle both because they fail together, and diagnosing the system rather than one symptom is what keeps a repair from coming back. Call (833) 962-9222 to schedule an assessment.
A stainless steel liner installation or a HeatShield repair is usually a one-day job, while a partial rebuild typically runs one to two days and a full rebuild takes longer depending on height and access. The schedule depends on flue condition, weather, and whether the crown and flashing are included. We give you a realistic timeline in the written scope before booking, and we don’t promise a date we can’t hold. Call (833) 962-9222 for an exact estimate and timeline.
Expect a stainless steel liner installation in the $2,400 to $4,800 range, liner repair around $1,200 to $2,600, a partial rebuild from $1,800 to $4,500, and a full rebuild from $6,000 up to $15,000 or more. The variables are flue height, liner diameter and insulation, roof access, and how much masonry has to be replaced. The written estimate sets the final price, and the camera inspection and photo report are included at no cost. Call (833) 962-9222 for an exact quote – estimates are free.
Yes. We install and service DuraFlex, HeatShield, Gelco, Olympia Chimney, and Famco, and we size each liner to the appliance it serves. We’re not a dealer and we don’t claim to stock parts, but we know these systems and where they wear out, from the top plate to the appliance connection. Whether you already have one of these brands or any other make, we can inspect, repair, or replace it. Call (833) 962-9222 to book.
Same-day service is often possible on booked sweeps and inspections, and dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, so a call that day is booked into the next opening. The phone line is answered 24/7, so you can reach us whenever the question comes up. Call (833) 962-9222. We answer 24/7.
Warranty terms depend on the product line and the scope of the work, and we put them in writing with your estimate rather than promising a blanket guarantee. Liner manufacturers set their own coverage, and our workmanship on the installation and rebuild is stated in the written scope. You’ll know exactly what’s covered before you commit. Call (833) 962-9222 and we’ll walk you through the details for your job.
Clear access to the fireplace and the chimney exterior, move anything breakable away from the hearth, and let us know about any previous liner or repair work so we know what we’re getting into. We contain the work area and clean up behind us, but a clear path to the roof and the firebox speeds the job. If you’ve just bought the property, have any inspection report ready. Call (833) 962-9222 to schedule.
If you’re comparing liner work across the region, our chimney liner & rebuild page covers Overbrook, and our full menu of chimney cap & crown work pairs well with any rebuild. For structural problems short of a full rebuild, see chimney repair, and for the firebox itself, fireplace repair. Routine upkeep belongs on the chimney sweep page.
Schedule Your Chimney Liner & Rebuild Service in Frankford Today
A liner that’s failed or a chimney that’s leaning won’t fix itself, and the camera will tell you exactly where you stand. Book a free estimate and get a written scope, a flat price, and a photo report you can review before anything is booked. Call (833) 962-9222. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. No obligation, and we’ll tell you plainly when work can safely wait.
Written by the team at Chimney Sweep Frankford.