Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Frankford Homeowners
You built a fire on a cold night, the draft worked, but weeks later there is a stain spreading across the ceiling near the chimney breast or a loose brick on the roof line. Chimney damage rarely announces itself. It shows up slowly: crumbling mortar joints, a crown that has split, rust on the damper, water finding its way into the attic. Our technicians have up to 15 years of experience reading exactly these symptoms, and we concentrate on chimney and fireplace systems alone. That focus is why we diagnose the whole venting system instead of patching the one spot you noticed. Whether it’s a cracked crown or a deteriorating liner, we diagnose the system, not just the symptom. Call (833) 962-9222 and we’ll book a visit. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

What Our Chimney Repair Service Includes
Chimney repair covers the masonry, the water management and the structural parts of the stack. We handle each piece as one system because a failure in one place almost always stresses another. Here’s what each repair involves and when it typically becomes necessary.
Mortar Repointing
Repointing means grinding out the failed mortar between bricks and packing fresh mortar into the joint, restoring the bond that holds the stack together. You need it when joints have receded, feel sandy to the touch, or show hairline cracks that let water in during a Frankford rain. We remove the deteriorated mortar to a consistent depth and refill the joint with a mix matched to the original brick, because a mortar that’s too hard can damage the brick it holds.
Spalling Brick Repair
Spalling is the flaking and popping of a brick face, usually caused by trapped moisture freezing and expanding inside the masonry. It shows up as brick fragments on the roof, in the gutter or on the ground near the stack. We replace the damaged bricks and address the water source that caused the spalling, so the new brick does not follow the same path. If the spalling traces back to a failed crown or flashing, we fix that too.
Chimney Waterproofing
Waterproofing is the application of a vapor-permeable sealant to the exterior masonry so rain sheds off while moisture inside the chimney can still escape. It is the right step any time the brick has been repointed or replaced, and it makes sense for older Frankford homes with porous brick. A sealer that traps moisture is worse than none, so we apply a breathable product suited to masonry, not a paint or a film.
Flashing Repair
Flashing is the metal work at the roof line that seals the joint between the chimney and the shingles. Loose, rusted or incorrectly stepped flashing is one of the most common causes of attic and ceiling leaks. We re-seat and re-seal the flashing, replace corroded sections, and check the counter-flashing where the masonry meets the metal.
Chimney Rebuilding
Rebuilding goes beyond surface repair when the upper section of a stack is structurally compromised, leaning, or has lost so many bricks that repointing will not hold. We take the stack down to sound masonry and rebuild it, matching brick and mortar and addressing the liner and crown at the same time. This is the kind of job sweep-only companies cannot take on, and it’s where our full-system approach matters.
Tuckpointing
Tuckpointing is a finer form of mortar work, cutting out failing joints and finishing them to a clean, even profile that improves both weather resistance and appearance. It’s the right call for a chimney that’s sound but looks tired, or where a homeowner wants the stack to match the brickwork of the house. We treat it as a repair, not a cosmetic afterthought, because water doesn’t distinguish between the two.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We work with materials from the professional-tier brands that credentialed chimney technicians rely on. HeatShield is a ceramic-based restorative product used for lining repair, and it lets us address a deteriorating liner in situations where a full reline would otherwise be needed. Olympia Chimney and DuraFlex supply the stainless components we use when a liner has to be replaced, and we choose the material and gauge to match your appliance and flue size rather than whatever is closest to hand.
Gelco and Famco are part of the product lines we work with when a repair involves caps, crowns and venting components, and knowing where each of these products wears out helps us spot problems general contractors miss. Whether the fix is a HeatShield application or a new stainless liner, the point is the same: the repair should match the system. Whether you have a HeatShield-lined flue, an Olympia Chimney cap, a Gelco installation or any other make, we can help.
Signs You Need Chimney Repair Right Now
Some symptoms can wait a few weeks and some should not. These are the ones worth calling about soon.
- Crumbling or sandy mortar. If the joints between bricks look recessed or you can scrub away mortar with a fingertip, the bond is failing. Left alone, the stack loses strength one course at a time.
- Water stains or a damp smell in the home. A brown ring on the ceiling above the fireplace or a musty odor when it rains points to a leak at the flashing or crown. Water and masonry do not get along, and the damage grows quietly.
- Brick pieces on the roof. Falling brick or flakes in the gutter or downspout mean spalling is active. The piece that comes loose could just as easily land on a walkway or a car.
- A leaning or visibly bowed stack. The chimney should be plumb. A tilt above the roofline signals structural movement, and that’s a job for a rebuild rather than a patch.
- Rust on the damper or firebox and poor draft. Rust indicates moisture inside the flue, and a weak draft may point to a damaged liner. Both are worth inspecting before the next burn season.
Our Chimney Repair Process – Step by Step
- 1
Inspection of the whole system. We look at the firebox, damper, flue, crown, flashing and exterior masonry, inside the house and out. Where a liner is involved we use camera inspection and include a photo report, so you see what we see.
- 2
A written scope and a flat price. We explain what’s failing, what caused it and what repair options exist, and we give you a written estimate with a flat price. That price is agreed before any work is booked, so there are no surprises later.
- 3
Repairs done in order of cause. We address the water source first, then the structural repair, then the surface work. That sequence is why a repointing job lasts when a quick patch does not.
- 4
Restoration with matched materials. Brick, mortar, cap and crown work is matched to the existing chimney and the home. Liner work uses professional-grade components from the brands we trust, sized to your appliance.
- 5
Final check and a clean site. We verify draft, inspect our own work and leave the area swept up. You get the sense of a job finished, not a job begun.
If you’ve recently bought an older Frankford property, our chimney repair service includes the full assessment a first-season homeowner needs before lighting the first fire.

See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Frankford?
Chimney repair in Frankford typically runs from a few hundred dollars for small masonry work up to several thousand for a rebuild, and the written estimate you get before booking sets the final price. These are estimated ranges for common scenarios, not quotes. A repointing job on a standard stack usually lands in the lower hundreds to about $1,200 depending on how much surface area needs work and how high the access is. Spalling brick replacement or flashing repair generally falls in a similar range, with flashing on a steep roof at the higher end. Waterproofing is the least expensive line item on its own, and it makes the most sense when combined with masonry repairs already underway. A full upper rebuild is the largest project, and it is worth getting a written scope for the liner and crown at the same time so the whole stack is addressed in one pass.
What affects the cost most is access, the amount of damaged material, and whether the problem is only masonry or extends into the liner and venting. A repair that fixes the cause is cheaper over time than repeated patches, but we’ll tell you plainly when a job can safely wait. To avoid overpaying, ask for a written estimate, ask whether the crown and flashing are included, and be wary of a company that quotes a liner without showing you camera evidence. We include the camera inspection and photo report in every estimate, and estimates are free.
Chimney Repair Near Frankford – Our Service Area
We work throughout Frankford and the surrounding communities, including chimney repair in West Philadelphia, Overbrook, Olney, Oxford Circle, Tacony, Kensington, Port Richmond, Merion Station, Narberth, Penn Wynne and Millbourne. Frankford jobs are usually scheduled within a short window, and for the outer neighborhoods we’ll give you an honest appointment time when you call. Whether the chimney is in a rowhouse or a detached older home, the first step is the same: an inspection and a written estimate. Call (833) 962-9222 to book a visit. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Serving Frankford, PA – Our Local Coverage Area
We serve Frankford and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Frankford
Chimney repair is the work of restoring the structural and water-shedding parts of a chimney: the masonry, mortar joints, crown, flashing, brick faces and, when needed, the flue liner. It is not the same as a chimney sweep, which cleans the flue, though the two often go together because cleaning reveals what repair is needed. We handle the whole system, from annual sweep to full liner rebuild, so you don’t need a second contractor. Call (833) 962-9222 for an exact quote; estimates are free.
Most small repairs, like repointing a section of masonry or resealing flashing, are completed in a single visit. Waterproofing and tuckpointing can take a day on a typical stack, depending on surface area and weather. A rebuild or a full liner replacement runs several days and depends on material availability and access. We’ll give you a realistic time frame with your written estimate before booking.
Chimney repair in Frankford generally ranges from a few hundred dollars for minor masonry and flashing work up to several thousand for a full upper rebuild. Repointing and tuckpointing typically sit at the lower end, while a rebuild or liner replacement is the larger project. The written estimate sets the final price, and it’s free with the inspection. Call (833) 962-9222 for an exact quote; estimates are free.
Yes. We work with HeatShield ceramic liner repair and with Olympia Chimney and DuraFlex stainless components for liner replacement. We also work with Gelco and Famco products where caps and venting are involved. If your liner was previously repaired or replaced, we’ll identify the material and match the repair to it. Call (833) 962-9222 to book an inspection.
Yes, same-day repairs are possible when the schedule allows, and we’ll tell you honestly on the call whether a same-day visit is realistic. We answer 24/7 for booking and questions. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
Our work is backed by the specialist who performed it, and warranty terms are set out in your written estimate so you know exactly what is covered before work begins. We stand behind the repair and will come back out if something we fixed doesn’t hold. Ask us about the specific terms for your project when we inspect. Call (833) 962-9222 to talk through the details.
Clear the area around the fireplace and hearth, and if you can, provide access to the attic and roof line so we can inspect the flashing and upper masonry. Move vehicles from the driveway if we’ll need ladder access to the roof. If you have a gas appliance connected to the flue, have the model information handy. We’ll confirm any other preparation when we book the visit. Call (833) 962-9222. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Schedule Your Chimney Repair Service in Frankford Today
Chimney problems get more expensive the longer they sit, and a crack in the crown or a failing flashing joint is not going to close itself. Our technicians have up to 15 years of experience, we work with the brands chimney pros rely on, and every estimate comes with camera evidence you can see for yourself. Call (833) 962-9222 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Frankford.