Gas fireplace service
Sweep & inspection
Caps & crowns
Flue relining
Masonry repairLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Why Frankford Homeowners Choose HeatShield Chimney Cleaning
We provide independent HeatShield chimney cleaning and resurfacing service in Frankford, and what sets our work apart is the order we do it in: the flue gets swept clean, water intrusion gets stopped at the crown and flashing, and only then does the HeatShield resurfacing go on. Get that sequence wrong and a new interior surface can fail inside a single heating season. We’re an independent HeatShield service provider, not affiliated with or authorized by the manufacturer, which means we can tell you honestly whether your flue qualifies for resurfacing or actually needs a full reline.
Frankford’s chimneys sit on some of Philadelphia’s oldest rowhouse stock, and those flues ask for that honesty. Call (833) 962-9222 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- HeatShield is a castable refractory resurfacing system troweled onto a damaged flue, not a liner you slide in.
- In Frankford’s old rowhouses the right sequence is sweep, stop the water, then resurface.
- We’re independent, so we have no incentive to push HeatShield where a stainless reline is the better answer.
- Every recommendation starts with a Level 2 inspection and camera evidence you can see.
Why Trust Chimney Sweep Frankford for Your HeatShield Chimney Cleaning?
Our technicians have up to 15 years of experience, and that time has been spent on chimney systems only. HeatShield work rewards that focus. The material is a proprietary refractory mix, and how it behaves depends on the flue it goes into: the profile of the clay tile, the tightness of the joints, how much glazed creosote is bonded to the walls, and whether the flue is pulling correctly for the appliance venting into it. A generalist who sweeps a few chimneys a month won’t read those signals the same way.
We work with quality parts that fit HeatShield equipment, and we work in a warranty-safe way. That means no generic “ceramic coating” standing in for the real mix, no sealing over a flue that wasn’t swept, and no resurfacing on top of an active water problem. We’re careful about documentation too, because a manufacturer’s warranty claim usually turns on whether the flue was properly prepared and whether the application matched the flue’s condition.
To be clear about who we are: we’re an independent HeatShield service provider. We’re not a HeatShield dealer, we don’t claim factory training or certification from them, and we don’t sell their products as a distributor. We repair, install and service HeatShield systems, and we tell you what the flue actually needs. From annual sweep to full liner rebuild, that’s one specialist, start to finish.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Common HeatShield Chimney Cleaning Problems We Fix in Frankford
These are the failures we run into most often on HeatShield jobs around Frankford, and the reason behind each one.
- Resurfacing applied over an unswept flue. Creosote left on the clay tile walls gets trapped behind the new surface. It can’t be brushed out afterward, and the bond between the refractory mix and the tile is compromised from day one. The sweep has to come first, always, and the flue has to be genuinely clean rather than quickly brushed.
- Coating that blisters or delaminates within a season. Almost always water. A bad crown or failed flashing lets rain in behind the resurfaced liner, and the moisture works the surface loose. Frankford’s summer downpours and freeze-thaw winters push water into uncapped flues, so we correct the crown and flashing before any HeatShield mix goes on.
- Smoke spillage after a job on an oversized flue. A flue that’s too large for the appliance won’t draft properly, HeatShield or not. Resurfacing without correcting flue size leaves you with a smoky fireplace and a surface that soots up fast. This is where an honest assessment sometimes points to a stainless reline from DuraFlex or Gelco instead.
- Homeowners told they have a “HeatShield liner” when they don’t. What’s actually in the flue is an unsealed clay tile stack that was never resurfaced. The giveaway is usually a rough, gritty tile interior instead of a smooth sealed surface. We check with a camera and show you what’s there.
- Cracked tile joints treated as a cleaning problem. Spalled or cracked clay tiles let gases past the flue wall. That’s a resurfacing candidate, but only after the flue is swept and the water source is handled. Cleaning alone doesn’t fix it, and no amount of brushing will.
HeatShield Parts & Our Repair-vs-Replace Approach
HeatShield resurfacing materials are proprietary. There’s no legitimate aftermarket substitute, and any quote that swaps in a generic ceramic coating in place of the real mix deserves a hard question. We use quality materials that fit HeatShield equipment and the flue they’re going into, and we don’t claim to stock genuine HeatShield parts or to be a dealer for them.
Repair versus replace comes down to the flue, not the sales pitch. If the clay tiles are cracked or spalled at the joints but the flue is sound in structure and the right size for the appliance, resurfacing is a real repair and usually the better answer. If the tiles have collapsed, the flue is badly oversized, or it has significant offsets, a HeatShield application won’t hold and we’ll say so. A stainless reline from DuraFlex or Gelco is the honest path in those cases.
If you’ve been quoted a HeatShield job and you’re not sure it’s justified, call (833) 962-9222 and we’ll look at the flue with a camera before anyone commits.
Our HeatShield Service Process – Step by Step
- 1
Diagnosis. A Level 2 inspection with a camera through the flue, checking tile condition, joint integrity, offsets, flue size against the appliance, and the state of the crown and flashing. You see the footage and the photos.
- 2
Creosote removal. A full sweep before anything else. Glazed creosote gets particular attention, because a bonded layer under new resurfacing is a failure waiting to happen.
- 3
Crown and flashing repair. Water intrusion stopped at the top before the flue interior is sealed. HeatShield crown and flashing repair mortars get used here where they fit the job.
- 4
Repair or install. HeatShield refractory resurfacing troweled onto a clean, dry flue, or a high-temp formulation where a solid-fuel flue needs it. Flue size is corrected where draft demands it.
- 5
Test. Draft verified, smoke test where it applies, and a visual check of the finished surface.
- 6
Warranty and records. Documentation of prep, materials and finished condition so a warranty claim later isn’t a guessing game.
See the difference
Before
After
Before
After
Before
AfterHeatShield Products We Service & Install in Frankford
We service and install across the HeatShield resurfacing range. That includes the HeatShield Original refractory resurfacing mix, a troweled ceramic liner for clay tile flues, and the HeatShield Plus high-temp formulation for solid-fuel flues where the heat load calls for it. We also use HeatShield crown and flashing repair mortars alongside resurfacing, since stopping water at the top is part of a job that lasts.
Beyond the material itself, a lot of our HeatShield work in Frankford involves evaluating the clay tile flue systems those mixes get applied to, much of it in the older rowhouse chimneys along the tight blocks off Frankford Avenue. Whether a given flue qualifies is a question the inspection answers, not the product label.
We Also Service These Brands
We aren’t tied to a single product line. Alongside HeatShield we install and service DuraFlex and Gelco stainless relining systems, and we work with Olympia Chimney, Famco and Copperfield as well. That range matters when a flue doesn’t qualify for resurfacing and a reline is the right move. You get one specialist who can do either.
FAQs – HeatShield Chimney Cleaning Service in Frankford
No. We’re an independent HeatShield service provider, not affiliated with or authorized by the manufacturer. We don’t claim factory certification or dealer status. What we do claim is the ability to assess your flue without a manufacturer incentive, which means we’ll tell you when HeatShield resurfacing isn’t the right answer.
HeatShield is a resurfacing system, not a liner in the usual sense. It’s a castable refractory mix troweled onto a damaged flue to form a smooth, sealed new interior surface over the existing clay tile. A stainless reline slides a new pipe inside the flue; HeatShield rebuilds the flue’s own interior surface. Both solve different problems, and the inspection tells you which one you’re facing.
Yes, without exception. Creosote left on the flue walls gets sealed behind the new surface, where it can’t be removed, and it weakens the bond. Skipping or rushing the sweep is one of the most common reasons a resurfacing job fails early. We sweep first and verify the flue is clean before any mix goes on.
Water, most often. A failed crown or bad flashing lets moisture in behind the resurfaced surface, and it blisters or delaminates within a season. Applied over an unswept flue is the other big one. Poor prep and uncorrected water intrusion account for most early failures, which is why we stop the water before we resurface. Call (833) 962-9222 if you’re seeing flaking inside your flue.
It can be, but only after the flue is evaluated for the appliance venting into it. Gas appliances produce their own moisture load, and a flue that’s oversized or already water-damaged needs that corrected before resurfacing. If it isn’t a fit, we’ll point you toward a stainless reline instead. The inspection decides, not a default answer.
HeatShield materials are proprietary, so there’s no legitimate generic substitute. Ask what mix is being applied and whether the flue will be swept and the water source corrected before application. A quote that skips those steps or describes a “ceramic coating” instead of HeatShield deserves a second look. Call (833) 962-9222 and we’ll walk you through what the job should include.
It depends on the flue. A straightforward resurfacing on a sound, correctly sized flue is a shorter job than one that needs crown repair, flashing work and creosote removal first. The written estimate lays out what your flue needs and what each step involves, so you know before anything starts.
The price is set per job by a written estimate, because a flue that also needs crown repair or a sweep ahead of resurfacing isn’t the same job as a clean resurfacing. Estimating by the flue’s actual condition is the only honest way to quote it. Call (833) 962-9222 for an exact quote, and estimates are free.
Will service void my HeatShield warranty?
Properly done service shouldn’t. Warranty problems usually trace back to prep and application: an unswept flue, uncorrected water intrusion, or a mix that wasn’t HeatShield. We document prep, materials and finished condition so there’s a clear record. We’re independent, so we can’t speak for the manufacturer’s terms, but we can make sure the work itself holds up.
Book Your HeatShield Service in Frankford, PA
Whether your flue needs resurfacing, a sweep, or a straight answer on whether HeatShield is the right call, we’ll look at it with a camera and show you what we find. From annual sweep to full liner rebuild, we handle the whole system. Call (833) 962-9222 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Frankford.