Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Cap & Crown Across Narberth
If your cap is loose, your chase cover is rusted, or the crown on your chimney has cracked, we can help. Chimney Sweep Frankford handles chimney cap and crown work across Narberth, from the Victorians near the train station to the newer factory-built fireplaces tucked into infill lots off Haverford Avenue. We know this borough’s tight driveways and steep slate and standing-seam roofs, and we plan the job around them. Call (833) 962-9222 to book an inspection. The estimate is free, and the written estimate sets the price.
Why Narberth Homeowners Call Chimney Sweep Frankford for Chimney Cap & Crown
Narberth’s reputation is built on 1895-era masonry, and plenty of borough chimneys still carry original brick. But a growing share of the homes here have factory-built fireplaces, and those units fail in their own way. A cracked chase top or a missing termination cap on a 1990s prefab fails exactly like an old one, except it takes a matching manufacturer part instead of mortar. That distinction shapes how we work in Narberth.
We handle every phase of chimney work, so the same specialist who inspects your cap can also assess the crown, the chase, and the flue liner in one visit. Our technicians have up to 15 years of experience, and our trade is chimney and fireplace systems only. No side work, no general handyman scope. We’ll show you a camera inspection and photo report so you can see what we see before anything is booked.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Cap & Crown Services in Narberth
Cap Installation in Narberth
A properly fitted cap keeps rain, birds, and debris out of the flue and keeps sparks in. On Narberth’s prefab units, that often means matching the cap to the flue collar the appliance was tested for, not forcing a generic cap onto a brand-specific chase. We work with termination caps from lines like DuraFlex and Olympia Chimney when the original is no longer seated correctly.

Cap Replacement in Narberth
Windstorms along Haverford and Narberth Avenues can knock a snap-in cap loose or dent it past sealing. When the original cap on a factory-built fireplace is a DuraFlex or Olympia termination, we pull the manufacturer spec for that chase, measure the flue collar, and fit a matching replacement. On the borough’s tight lots with steep rooflines, that work is usually staged from ladder stands and roof jacks rather than a truck platform.

Crown Repair in Narberth
A chimney crown is the concrete or mortar cap at the top of the masonry that sheds water away from the flue. On Narberth’s older homes, the soft brick and mortar take a beating from the freeze-thaw cycle, and crowns crack at the chase edge. Repairing a crown means rebuilding the slope and sealing the joints so water runs off instead of into the chimney structure. We diagnose the system, not just the visible crack.

Crown Coating in Narberth
When a crown has hairline cracks but is structurally sound, a coating can seal it before the damage spreads. Southeastern PA’s humid summers and freeze-thaw winters drive spalling in old brick and mortar, and an unsealed crown lets that moisture in year after year. Coatings are a preventative step, not a substitute for repair. If the crown is failing structurally, we’ll tell you so and explain what repair involves.
We also install chimney cap & crown systems on multi-flue chimneys, where more than one flue opens at the top and each needs its own protected termination. Multi-flue caps on the attached and twin homes near the train station often need a custom fit.
Trusted Brands We Service in Narberth
We work with professional-grade product lines that credentialed chimney technicians rely on, including DuraFlex, HeatShield, Olympia Chimney, Gelco, Famco, and Copperfield. These aren’t brands pulled from a big-box shelf. They’re specified for the appliance and the chase, and that matters most on Narberth’s prefab fireplaces, where a brand-specific termination cap either seats on the flue collar or it doesn’t. When we need a part for a Narberth job, we source it to the manufacturer spec and work with you on timing.
Common Chimney Cap & Crown Problems We See in Narberth Homes
- Rusted-through chase covers on factory-built units. Factory-built chase covers rust through at the seams within a decade, so water runs into the chase and rusts the damper and firebox instead of failing visibly at the roofline. By the time you notice a damp firebox, the corrosion has had time to work.
- Brand-specific termination caps that no longer seat. The original cap on a prefab unit is brand-specific (DuraFlex, Olympia, Famco), and a generic cap either won’t seat on the flue collar or blocks the draft the appliance was tested for. A windstorm can shift the original cap out of position even when it looks intact from the ground.
- Cracked prefabricated crowns on newer homes. Prefabricated crowns crack at the chase edge from freeze-thaw, and because nothing looks old, many homeowners skip the annual Level 1 inspection until spalling or a downdraft appears. A newer chimney still has seams that open over time.
- Party-wall and shared flues in attached and twin homes. Many borough chimneys near the train station serve shared or party-wall flues, and that changes how a cap or crown gets installed. A cap that fits one flue opening may not protect the adjacent one, so the installation has to account for both.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Cap & Crown in Narberth, PA
Typical chimney cap and crown work in Narberth runs in the ranges below. Prices are estimates and the written estimate sets the final price.
- Single-flue cap installation: typically $150 – $450, depending on flue size and whether a stock or custom cap is needed.
- Multi-flue or custom cap: typically $350 – $900, driven by the number of flues and the chase dimensions.
- Cap replacement on a factory-built chase: typically $200 – $600, including the chase cover and flashing seal.
- Crown repair: typically $400 – $1,200, depending on the size of the crown and how much rebuilding is required.
- Crown coating: typically $250 – $700 for a sound crown with hairline cracks.
What moves the number: the number of flues, whether the cap is stock or custom, whether the crown needs full rebuilding or just sealing, and roof access. Narberth’s steep slate and standing-seam roofs often require ladder stands and roof jacks, and that affects labor. Every job starts with a camera inspection and photo report, and the flat price is agreed before booking.
We Also Serve Cities Near Narberth
We also serve homeowners in Merion Station, Penn Wynne, Overbrook, and Millbourne. The housing stock shifts as you cross out of the borough, but the cap and crown problems are familiar. If you’re not sure whether your address falls in our Narberth service area, call and we’ll confirm. Estimates remain free.
Serving Narberth, PA – Our Local Coverage Area
We serve Narberth and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Cap & Crown in Narberth
Because factory-built chase covers and prefab crowns fail from rust and freeze-thaw just like older masonry, and the damage is often hidden. A rusted chase cover lets water track down the chase and rust the damper and firebox before anything shows at the roofline. The original termination cap can also shift out of position after a windstorm even if it looks fine from the ground. A Level 1 inspection catches it early. Call (833) 962-9222 for an inspection.
On most prefab chases, the termination cap should match the appliance’s flue collar, so a brand-specific part is usually the safer choice. A generic cap either won’t seat properly or blocks the draft the appliance was tested for. We pull the manufacturer spec for your chase, measure the flue collar, and fit a matching cap or a custom one when the original isn’t available. Call (833) 962-9222 and we’ll confirm what your unit needs.
The usual fix is a new chase cover sealed at the flashing, plus a matching cap if the original termination is no longer seated. Water entering at the rusted seams tracks down the chase and shows up as a damp firebox or a rusted damper, which is exactly what you’re describing. Isolating the leak starts with inspecting the chase top, the flashing, and the cap during a single visit. Call (833) 962-9222 to book that inspection.
Yes, especially on a factory-built fireplace, because the failure modes on newer units don’t show up as visible age. Chase covers rust at the seams, prefab crowns crack at the chase edge through freeze-thaw, and termination caps shift after storms. None of that reads as “old” from the ground. A Level 1 inspection with a camera check is the fastest way to know what’s really happening. Call (833) 962-9222 and we’ll schedule it.
It often does, because a shared flue means the cap and crown have to account for more than one opening and for how the shared stack is structured. A cap designed for a single flue may not protect the adjacent flue, and the crown repair has to work around the party wall. Many borough chimneys in attached and twin homes near the train station fall into this category. Call (833) 962-9222 and we’ll assess the setup before recommending anything.
Book Chimney Cap & Crown Work in Narberth
Whether your Narberth home has an 1895 brick chimney or a 1990s prefab with a rusted chase cover, we can help. Call (833) 962-9222 to book an inspection and free estimate. The flat price is agreed before anything is scheduled. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Frankford.